- argedo nch02 ncd02 3 4
Brand Name: Argedo
Model Number: NCH02 NCD02
- 1 x 3/4/5 Axis DSP Control System (we will ship as you choose)
- 1 x 4G U-Disk Flash
- 1 x CD (English Manual, plug in)
This is 3/4/5 Axis DSP manual CNC controller. It can read and run G-CODE from U-disk and replace for GRBL. You could operate without computer.
This controller can be applied to engraving machine, CNC machine and automatic production line.
- Read G-CODE from U-DISK;
- Operation without computer;
- 8 ports photoelectric isolated input interface;
- 5 ports photoelectric isolated output interface
- 1 port 0-10V spindle speed analog output interface (can change to PWM output);
- Can support 3/4/5 axis stepper systems, 125 KHz pulse output for every axis;
- ARM motion control chip;
- Main device is 24VDC power supply input; current should higher than 1A;
- Support standard MPG and NVMPG;
- 3.5'' TFT screen;
- 19 user key
Appearance and size
- The Hand control system NCH02 appearance as the Figure 1-1 show: The host system NCD02 appearance as the Figure1-2.
- The Hand control system NCH02 overall size is 168mm*108mm*30mm;
- The host system NCD02 overall size is 100mm*70mm*23.5mm
When operate the NCH02, where will be a lot of English abbreviation, now we list all of them for your kindly references:
FRO: Feeding adjusts: During the operating process, the F value already set, and need to adjust the current feeding speed, then we can adjust FRO value to realize it.
SRO: Spindle speed adjust: During the operating process, the S value already set, and need to adjust the current spindle speed, and then we can adjust SRO value to realize it:
Current Speed S#=setting S*SRO.
SRJ: speed adjust manually
During the operating process, as the manual speed already set, and we need to adjust the current speed, and impossible to fix the value during it is working, then we can revise the SRJ value to realize it.
Current manual speed FS#=Setting manual speed*SRJ.
F: Feedingspeed, the unit is mm/min. For example F=200, means every minute feeding
S: Spindle Speed. Unit is rad/min. For example S=20000, means 20000 revolution/Minute.
- X axis Coordinate
- Y axis Coordinate
- Z axis Coordinate
- A axis Coordinate
- B axis Coordinate
- C axis Coordinate
Ready: ReadyMode. In the mode we can do any operation, include processing or values modification or starting 2nd mode.
Reset: Reset mode. In this mode, it should stop every operation.
“Step”: Manual Step Mode. Every axis can conduct the manual step operation at this mode.
MPG: MPG mode. Every axis can conduct the MPG operation at this mode.
Port Definition and connection
As shown in Figure 2-2, the main controller indicates 1-7 are USB port, main power port, general input port, general output port, MPG port, spindle port and stepper motor control port.
The detailed description of these functional modules and interfaces is described below.
2.3.1 USB port
As Figure 2-2 showed, No.1 terminal block is USB port, you can connect with NCH02 through this interface.
2.3.2 Main power supply port as the Figure 2-2 show, the marked No. 2 port is power supply port. The access voltage range is 24VDC, and the power is not less than 20W. The positive and negative connection of the power supply see as the silk printing, See as Figure 2-2, left is GND, and right is "+". 2.3.3 Limit/Home input port
EU Ship!3/4/5 Axis NCH02 G-code Controller Board NC Card USB CNC Motion Control System For Engraving Machine replace DSP A11E
NCD02 3 axis 4 5 Mach3 USB CNC controller engraving milling machine stepping servo off line single replace
ARGEDO SUMACH MACH3 4 Axis USB CNC Motion Control Card Breakout Board 150 KHz 5V DC Analog PWM support MPG for DIY Machine
DE ship 3Axis/ 4Axis/ 5Axis NC Card USB CNC Motion Control System Controller Board NCH02 G code For Router replace DSP A11E
ARGEDO CNC USB 4 Axis MACH3 100 KHz Motion Control Card Breakout Board 12-24V for Engraving Free Drive
Коллектор STOUT распределительный 3/4 на 3 выхода 3/4ЕК (SMB 6851 343403)Производитель: STOUT